Brakes
Squeaky Brakes, Grinding or a Soft Pedal: What Brake Noises Mean
Squeaky brakes usually mean the brake pads are getting thin and a built-in wear indicator has started to rub the rotor. A grinding noise usually means the pads are worn through and metal is scraping metal, so book a repair right away. A spongy pedal, a pedal that sinks, or a car that pulls hard when you brake is a safety issue: get it checked before you drive much further.
Here is what each symptom usually means, how urgent it is, and why Ottawa driving is harder on brakes than most.
Brake noises and warning signs at a glance
- A brief squeak on the first few stops after rain or an overnight park: usually moisture or surface rust on the rotors. Normal if it goes away quickly.
- A squeal that keeps coming back: the pads are likely near the end of their life. Book an inspection soon.
- Grinding or scraping: the pads are likely worn to the metal. Book right away and drive as little as possible.
- A pulsing pedal or shaking steering wheel when braking: uneven rotors. Book soon.
- A soft, spongy or sinking pedal: possible air, moisture or a leak in the hydraulic system. Stop driving and get it checked.
- Pulling to one side when braking: often a sticking caliper. Get it checked promptly.
Brakes squeaking or squealing
Not every squeak is a problem. After a wet night or a car wash, a thin layer of rust forms on bare rotors, and the first few stops can squeak or feel slightly rough. If the noise disappears within a few stops, that is normal.
A squeal that keeps returning is different. Many brake pads have a small metal tab that touches the rotor when the friction material gets low. It is designed to make an annoying high-pitched noise so you know it is time for new pads. Some vehicles use an electrical sensor in the pad instead, which turns on a dash warning light. Either way, the pads should be inspected and probably replaced soon, while the rotors are still in good shape.
Squeaky brakes can also come from brake dust, glazed pads or hardware that has lost its lubrication. You can't confirm the cause by listening, which is why a technician needs to look at the pads.
Brakes grinding noise
Grinding brakes are the urgent version of a squeal. When the pad material is gone, the steel backing plate presses on the rotor. By then braking efficiency has dropped to the point of being unsafe, and every stop gouges the rotor, which can turn a pad replacement into a pad-and-rotor job.
A grinding sound can also come from a stone caught between the rotor and its shield, or from a seized caliper dragging a pad. Whatever the cause, grinding means booking the earliest appointment you can and avoiding highway driving until it is fixed.
Pulsing pedal or shaking wheel: the "warped brake rotor"
If the brake pedal pulses or the steering wheel shakes when you slow down from highway speed, most people call it a warped brake rotor. In most cases the rotor is not actually bent. The usual cause is uneven rotor thickness or pad material deposited unevenly on the rotor surface, which makes the pads grab and release as the rotor turns. Depending on how much material is left, the fix is resurfacing or replacing the rotors, along with new pads.
One exception: if you brake hard on ice or snow and feel a rapid buzzing pulse under your foot, that is the anti-lock brake system (ABS) working. Keep firm pressure on the pedal. That pulse is normal. A pulse during ordinary, gentle stops on dry pavement is not.
Spongy brake pedal or soft brake pedal
A spongy brake pedal feels mushy and travels further than usual before the car slows. Common causes include:
- Air in the brake lines, often after a repair or a leak.
- Old brake fluid. Brake fluid absorbs moisture from the air over time, which lowers its boiling point. Under heavy braking the fluid can boil and form gas bubbles, and the pedal goes soft.
- A fluid leak at a line, hose or caliper. Corroded steel brake lines are a known problem on vehicles that spend years on salted roads.
- A failing master cylinder, which can let the pedal slowly sink while you hold it.
A soft brake pedal is not something to wait on. If the pedal sinks toward the floor, the brake warning light stays on, or you see fluid near a wheel, pull over safely and arrange a tow rather than driving on. Topping up the fluid does not fix the cause.
Car pulls to one side when braking
If the car drifts left or right only when you brake, one side is gripping harder than the other. The most common reason is a caliper or caliper slide pin that is sticking, so one wheel brakes harder or drags. A sticking caliper can also cause a hot wheel, a burning smell after a drive, and one pad wearing much faster than the other. Contaminated pads or a damaged brake hose can cause the same symptom. If the car pulls all the time, not just when braking, the cause is more likely tires or wheel alignment. Our guide to tire tread depth and age explains what uneven tire wear can tell you.
How Ottawa road salt and stop-and-go driving wear brakes
Brakes in Ottawa work harder than brakes in milder places, for two reasons.
Salt. The City of Ottawa treats roads with dry salt, wet salt and liquid brine through the winter, and freeze-thaw cycles keep roads wet and slushy for months. Salt spray washes the grease off caliper slide pins and lets rust build up on them. Once a slide pin seizes, the pads can't move freely: one pad wears down to nothing while the other still has material, or a pad stays pressed against the rotor after you lift your foot. That is why seized calipers, uneven pad wear and rusty rotor edges are so common by spring.
Stop-and-go traffic. Brake pads wear fastest in city driving. A commute along Carling Avenue or Hunt Club Road, with frequent traffic lights and rush-hour queues, uses the brakes far more than the same distance on an open highway. Commuters coming in from Kanata on the Queensway (Highway 417) or from Orléans on Highway 174 get gentler highway kilometres, until traffic slows to a crawl. Drivers in Nepean who mostly make short trips around town often wear pads faster than their kilometres suggest.
A practical habit: have the brakes inspected once salt season ends, and have the slide pins cleaned and lubricated if they are sticking. It is also easy to have the brakes looked at when the wheels are off for your seasonal tire change.
How long do brake pads last?
There is no single answer. Brake pads can last anywhere from about 25,000 km to 150,000 km, depending mostly on how you drive. Mainly highway driving sits at the long end. Heavy city commuting with lots of stop-and-go traffic can wear a set down far sooner. Last-second hard braking, resting a foot on the brake pedal and carrying extra weight all shorten pad life. Sticking calipers do too, because they keep the pads rubbing.
When to replace brake pads
Go by condition, not a calendar. Replace brake pads when:
- An inspection shows the pad material is getting thin.
- You hear a squeal that keeps returning, or a pad wear light comes on.
- One pad on an axle is wearing much faster than the other.
- You hear grinding. At that point you are overdue, and the rotors may need work too.
Your owner's manual lists when to inspect the brakes and when to change the brake fluid, since intervals vary between vehicles.
Book a brake inspection at Janex
If your brakes are squeaking, grinding, pulsing or feel soft, the Janex Automotive service department at 1138 Carling Ave can inspect them and explain what needs doing now and what can wait. Book online and a service advisor will call to confirm your time, or call 613-686-5577. Service hours are Monday to Friday, 8:30AM to 5:30PM. If the pedal is sinking or the brake warning light stays on, arrange a tow rather than driving the car in.