Diagnostics and check engine light

Check Engine Light On or Flashing? What It Means and What to Do

By Janex Service ·

Car dashboard at dusk with the amber check engine light on

The check engine light means your car's computer has found a fault in the engine, ignition, fuel or emissions system and stored a trouble code. A steady light usually means you can drive carefully and should book a diagnosis soon. A flashing light means pull over and stop driving, because the engine is most likely misfiring and can quickly damage expensive parts.

What does the check engine light mean?

Every modern car monitors itself. Sensors report on the air and fuel mixture, the ignition, the exhaust and the fuel vapour system, and when a reading falls outside its normal range the engine computer saves a code and turns on the light. On most cars the light also glows for a moment when you turn the key, as a bulb check. If it stays on after the engine starts, a code has been stored.

The light covers both engine faults and emissions faults, so on its own it doesn't tell you how serious the problem is. It could be a loose gas cap or a failing ignition coil. Check your owner's manual too, since some vehicles use separate yellow and red warnings that mean different things.

Check engine light on vs flashing

Steady check engine light

A light that comes on and stays on usually points to a fault that affects fuel economy and emissions but isn't causing immediate harm. The car may feel completely normal. It still needs attention: a small fault left for weeks can turn into a bigger repair, and a second problem can appear without you noticing, because the light is already on.

Check engine light flashing

A flashing light is the urgent one. It most often means an active engine misfire: one or more cylinders aren't burning fuel properly. Unburned fuel then goes into the exhaust, where it can overheat and damage the catalytic converter, one of the more costly parts on a car. Common culprits are worn spark plugs, failing ignition coils and damaged plug wires. You may also feel shaking, rough idling or a loss of power.

Can I drive with the check engine light on?

  • Steady light, car drives normally: generally yes, for a short time. Drive gently and book a diagnosis in the next few days.
  • Steady light with symptoms: if the engine runs rough, loses power, stalls, smells of fuel or burning, or the temperature or oil pressure warning comes on, stop as soon as it's safe.
  • Flashing light: no. Pull off the road safely, shut the engine off and arrange a tow rather than driving to a shop.

On the Queensway (Hwy 417) from Kanata or the 174 from Orléans, that means taking the next exit or getting well onto the shoulder, not slowing down in a live lane. In winter, keep warm clothing in the car so you can wait safely if you do have to stop.

Common causes of a check engine light

  • Loose, damaged or missing gas cap, one of the most common and cheapest causes
  • Oxygen (O2) sensor giving bad readings about the exhaust
  • Mass airflow sensor that is dirty or failing
  • Spark plugs, ignition coils or plug wires causing misfires
  • Catalytic converter problems, often after a misfire was ignored
  • Vacuum leaks from cracked hoses or gaskets
  • Battery or charging system faults that upset the car's electronics

Several of these produce the same symptoms, which is why the stored code matters more than the symptom you can feel.

Loose gas cap and the check engine light

The gas cap is part of the evaporative emissions (EVAP) system, which keeps fuel vapour sealed inside the tank. If the cap is loose or its seal is cracked, the system reads that as a leak and turns on the light. Some cars show a separate "check fuel cap" message; many simply show the check engine light.

The light usually doesn't appear right at the pump. It comes on after the car runs its leak self-test, often within a day or two of filling up. If that matches what happened to you, and the car runs normally with no other warning lights:

  1. Remove the cap and check the rubber seal and the filler neck for cracks or debris.
  2. Put the cap back on and tighten it until it clicks, if your cap is the clicking type.
  3. Drive normally for a few days.

The light won't go out the moment you tighten the cap. The leak test doesn't run on every drive, only under certain conditions (for example, the tank can't be nearly empty or completely full, and many cars skip it in extreme cold, around -18°C and below). During an Ottawa cold snap it can take longer than usual for the light to clear. If it stays on or returns, have the code read. The same leak code can come from a cracked vent hose or a faulty valve elsewhere in the system, and a new cap won't fix those.

What to do right now

  1. Note whether the light is steady or flashing. This decides everything else.
  2. Check how the car feels and look at the other gauges, especially temperature and oil pressure.
  3. If it's flashing, or the car runs badly, pull off safely, turn the engine off and call for a tow.
  4. If it's steady and the car drives normally, check the gas cap, then drive gently and avoid hard acceleration until it's looked at.
  5. Book a diagnosis instead of waiting for the light to go away on its own.

Why a code read beats guessing

A trouble code points to a system, not a specific part. A misfire code, for example, can come from a spark plug, a coil, a fuel injector or a vacuum leak. Many parts stores will read the code for free, but reading a code isn't the same as diagnosing the car: it tells you which systems may have failed, not which part to replace.

Guessing usually costs more. Replacing an oxygen sensor because the internet said so won't help if the real fault is a leaking intake hose, and clearing the code with a cheap scanner only switches the light off until the fault is detected again. A proper diagnosis reads the code and the data saved when it was set, tests the suspect parts, and confirms the repair actually fixed the problem.

Driving from Kanata, Orléans or Nepean

Most check engine lights show up on ordinary days: the commute in from Kanata, a run along the 174 from Orléans, errands around Nepean or a trip over to Gatineau. If the light is steady and the car feels normal, there's no need to cancel your day, but don't let it ride for weeks either. Carling Avenue is reachable from all of these areas, so booking a diagnosis can fit around your usual route.

If your car is also slow to start on cold mornings, a tired battery may be part of the story. Our guide to car battery life in winter covers the warning signs, and regular maintenance like changing your oil on schedule helps prevent some of the faults that trigger the light.

Book a check engine light diagnosis at Janex

The Janex Automotive service department at 1138 Carling Ave in Ottawa can read the code and diagnose the cause. Book online and a service advisor will call to confirm your time, or call us at 613-686-5577, Monday to Friday, 8:30AM to 5:30PM. If your light is flashing, please don't drive the car in; have it towed to us instead.

Book your service at Janex

Request a time online and a service advisor will call to confirm. We're on Carling Ave, an easy trip from Nepean, Kanata, Orléans and anywhere in Ottawa.